Reset your Holosun EPS Carry Red Dot Sight

Occasionally, you may need to reinitialize your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the configurations or are experiencing unexpected behavior. Fortunately, resetting your Holosun is a simple process that can be performed in just a few steps.

Begin by ensuring your red dot sight is activated.
Find the small button for reset on the side of the sight.
Utilize a small object to depress the reset lever for approximately 7 milliseconds.
Release the lever and your Holosun EPS Carry Red Dot sight will power cycle.
Your red dot sight should now be reverted to its factory settings.

Restore Your Holosun EPS Carry Red Dot back to Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to return to original, resetting it to default configuration is a breeze. First, find the tiny button on the bottom of your optic. Then, keep pressed it for around five seconds until you see the red dot blink. Your Holosun EPS Carry is website now reset to its factory settings, ready for precise aiming.

Bring Your Holosun EPS Carry Back to Action

Is your beloved Holosun EPS Carry experiencing some performance problems? Don't despair! A simple factory reset can often resolve the problem and get your red dot sight back to its former glory. Before you begin, remember to disconnect the battery from your Holosun EPS Carry to prevent unintended activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these straightforward steps:

Hold down the power button for approximately 7 seconds.
A message will flash, indicating that the reset is being performed.
Stop pressing the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can connect the battery and test your sight's functionality. If you encounter any further difficulties, don't hesitate to contactsupport team.

Revert Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Follow these steps carefully to ensure a successful factory reset.

Initially, Activate your Holosun EPS Carry by pressing the power button.
Next, press and hold both the mode button and the up/down adjustment button simultaneously.
While continue holding these buttons, press the power button once.
The display will show a confirmation prompt indicating that the reset process is initiated.
Permit the process to finish. This may take a few moments. Once done, your Holosun EPS Carry will automatically shutdown.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Clear All Settings on Your Holosun EPS Carry

To Factory reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Pressing a specific button combination. Consult your Instruction for the exact button sequence for your model. Once in the settings menu, look for an option that says "Reset All". Select this option and confirm the reset. Your sight will then power off and restart with all settings Reinitialized to their default values.

Reinitialize your Holosun EPS Carry with a Factory Original Settings

If your Holosun EPS Carry is acting erratically, a factory reset might be the answer. This will restore your sight to its factory settings, clearing any altered configurations you've made. To execute this reset, observe these simple steps:

To begin, find the reset button on your EPS Carry.
Secondly, use a small object, like a pen tip, to push the reset lever.
As you maintain the reset switch engaged, activate your EPS Carry.
It will flash a message showing that the reset is successful.

After the reset is successful, your EPS Carry will be returned to its factory settings.